Understanding How Horizontal Drilling Rigs Work In Modern Drilling Operations
| Drilling step | What the operator monitors | How the drill head is steered | Practical example or consideration |
|---|---|---|---|
| Plan the bore path | Entry and exit locations, target depth, required clearance, and the planned horizontal and vertical alignment. | The operator compares guidance readings with the planned line and profile, then makes gradual corrections rather than abrupt changes. | A bore profile accounts for the ground conditions, nearby utilities, and the bend limits of the drill string and product pipe. |
| Locate the transmitter | A locating receiver detects the signal from a transmitter behind the drill head. Depending on the system, readings can include depth, pitch, roll, and direction. | The locator tracks the transmitter from the surface; the operator uses its position and orientation readings to assess the head's location and alignment. | Depth is generally a calculated locating measurement, not a direct measurement of the entire bore's vertical profile. System limits and site conditions affect readings. |
| Read head orientation | Pitch shows the head's upward or downward inclination; clock-face or roll information indicates the orientation of its steering face. | The operator aligns the drill string so the angled steering face points toward the intended correction. | For example, an upward-facing steering face can help create an upward curve when the drill string is pushed without rotation. Actual response depends on the tooling and ground. |
| Make a steering push | The locator's updated position and orientation, along with the rig's thrust and rotation controls. | The rig pushes the drill string while the operator holds the steering face at the selected orientation. The angled face tends to deflect the head in that direction. | Steering is incremental: the operator checks progress and adjusts the face orientation as needed to follow the planned path. |
| Advance in a straighter direction | Whether the measured head position and pitch are tracking the intended bore line. | The operator rotates the drill string as it advances. Rotation changes the steering-face direction over time, reducing the consistent directional bias of a non-rotating push. | Rotation is commonly used to maintain or advance along a relatively straight section; the resulting path still depends on ground and tooling response. |
| Check and correct the trajectory | Successive location readings, depth, pitch, and the difference between the measured position and the planned profile. | The operator alternates between controlled steering pushes and rotation, using new readings to decide whether a correction is needed. | Frequent checks help identify deviation early. Magnetic interference, signal conditions, and difficult ground can affect locating and steering decisions. |
| Complete the pilot bore | The head's approach to the planned exit location, plus the final measured alignment and depth. | The operator makes the final gradual steering adjustments while maintaining communication between the locating and rig teams. | After the pilot bore reaches the exit, the hole is typically enlarged with one or more reaming passes before product pipe is pulled through. |
Note: Steering response and locating accuracy vary with the guidance equipment, drill-head design, soil or rock conditions, and site interference. Operators follow the equipment instructions and project-specific tolerances.
Circulating Drilling Fluid and Removing Cuttings
A horizontal drilling rig pumps drilling fluid down the drill string and back through the annular space around it. The returning fluid carries cuttings-small pieces of soil or rock-to the surface. There, screens and settling tanks separate solids so the fluid can be checked and reused. This circulation cools the bit, supports the borehole walls, and helps prevent cuttings from packing around the drill string. The North American Society for Trenchless Technology's HDD Good Practices Guidelines and API Recommended Practice 13D both stress monitoring fluid properties and operating conditions. For scale, a simplified calculation for a 200 mm bore with a 100 mm drill rod gives about 0.071 m/s annular velocity at 100 L/min. Actual flow is affected by bore shape, fluid losses, and cuttings loading, so that figure is not a universal target: Watch the return flow and compare it with the pump rate. A sudden drop, thick returns, or a growing pile of cuttings can signal poor transport or fluid loss. Check density and rheology regularly; API RP 13D describes measurements such as plastic viscosity, yield point, and gel strength. Don't rely on appearance alone. I'd also recheck the assumptions behind any flow calculation-the bore is rarely as neat as the drawing.
Enlarging the Bore with Reaming
After a horizontal drilling rig creates a pilot bore, reaming enlarges the passage to the required diameter. The crew attaches a reamer behind the drill string and pulls it back through the bore. Its cutting surfaces loosen soil or rock, while drilling fluid helps carry cuttings toward the entry pit. The chosen reamer depends on ground conditions and the pipe's outside diameter. Bigger is not always better.
Some bores need several reaming passes, increasing the diameter gradually. This can reduce strain on the rig and help limit ground disturbance, though results vary with soil, rock, and groundwater. Operators monitor pullback force, rotation, and fluid returns for changes. A sudden rise in resistance may signal a blockage or unstable ground. Pause and assess. Reaming can look straightforward from the surface, but the bore itself is hidden; that uncertainty deserves respect.
Tips: Match the reamer to the ground, and follow the drilling plan's target size. Keep fluid circulation steady, but watch for unexpected losses or returns. Clear communication between the operator and the crew matters during pullback. Record changing forces and ground conditions; small details can explain a difficult pass later. A neat surface tells only part of the story.
Pulling the Product Pipe into Place
Once the bore is complete, the drill string is withdrawn and the product pipe is connected to a pullback assembly. A swivel sits between the reamer and pipe, helping prevent drilling rotation from twisting the pipe. The crew checks each connection and confirms the pipe is supported without sharp bends rig then pulls the assembly back through the bore. As it moves, the reamer may enlarge or condition the path, while drilling fluid helps carry cuttings out and reduce friction. Operators watch pull force, rotation, fluid returns, and pipe movement. A sudden rise in pulling force can signal an obstruction or changing ground conditions. Pause and assess; forcing the pipe can damage it. This part looks straightforward, but the ground can surprise you: Keep the pipe aligned with the bore entrance. Track pullback readings, and inspect connections as the pipe advances. Follow the pipe and rig manufacturers' limits; a number that seems acceptable may not suit every soil or pipe. Clean fluid returns matter, too. If returns change or stop, reassess before continuing the exit pit, workers guide the pipe clear of the tooling and protect its end from impact. The finished line should be checked for visible damage and documented before the rig is moved. A careful record helps explain any unusual pull forces later.
Conclusion
How Does A Horizontal Drilling Rig Work? The process begins with preparing the work area and positioning the rig along the planned route. Its main components, including the drilling unit, drill string, steering system, and fluid circulation equipment, work together to create a controlled underground path. The crew first drills a pilot bore, guiding the drill head while monitoring its position and direction to keep it on course drilling, fluid circulates through the bore to cool and lubricate the drill head, carry cuttings back to the surface, and help stabilize the hole. Once the pilot path reaches its destination, the crew attaches a reamer and pulls it back through the bore to enlarge the opening. After the bore is wide enough, the product pipe is connected and pulled into place. Careful setup, steering, fluid management, and reaming help make the installation accurate and efficient while limiting disruption at the surface.
About Us
Baoji Mengtai Petroleum Machinery Co., Ltd.
Was established on July 15, 2003, and is headquartered in Baoji City, Shaanxi Province, the same city with BOMCO a leading manufacturer of petroleum machinery and components, we were among the first outstanding enterprises in our local industry to begin exporting our products and engage in both import and export business.
Legal Disclaimer:
MENAFN provides the
information “as is” without warranty of any kind. We do not accept any
responsibility or liability for the accuracy, content, images, videos,
licenses, completeness, legality, or reliability of the information
contained in this article. If you have any complaints or copyright issues
related to this article, kindly contact the provider above.

Comments
No comment